HOW TO SET UP A TUB: INSTALL AN ACRYLIC BATHTUB AS WELL AS TUB SURROUND

How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround

How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround

Blog Article

Schedule An Appointment

How do you actually feel in regards to A Step-by-Step Guide to Installing a Bathtub?


How to Install a Bathtub Yourself
Installing a bathtub isn't specifically rocket science, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately tough job. If the old bathtub is readily obtainable, the job can move easily; if you have to open up a wall surface to remove the old bathtub and place the new bath tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will require a helper to leave the old tub and also embeded in the new one. Make sure you have actually certified yourself for the task and are comfortable trying it. As opposed to employing a professional to take over a halfway-completed project, it is much better to consider utilizing one before you start. Opportunities are you may need a specialist plumber to make tube connections.
This write-up will certainly aid you install a brand-new tub in your bathroom if you have actually already gotten a brand-new tub as well as do not need to transform the setup of your previous supply of water pipelines.
Your tools as well as product checklist ought to consist of the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipeline Caps


  • Removing Old Taps


    If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you need to do is disconnect the water supply. After doing so, turn on the taps to drain any water staying in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the limited access that is commonly the case.
    Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipelines have actually been gotten rid of, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any old securing substance.
    Before proceeding to fit the new taps, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.

    Fitting New Taps


    If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a link to the existing supply pipes.
    If you need to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
    Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in location between the faucet and the sink. Safeguard the faucet in place with the supplier supplied backnut. Once the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former kind must be connected to the faucet ends initially, tightening just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

    Mounting the Bathtub


    Making use of the two wood boards under its feet, position the bathtub in the called for position. The wood boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little factors.
    The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the bathtub up until the level reviews level.
    To install faucets, fit the bottom of the outermost versatile faucet adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the various other tap.
    Activate the supply of water and also check all joints and also new pipework for leakages and tighten them if needed. Load the tub as well as additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
    Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the tub ought to wait till the bath tub has been used a minimum of when as this will certainly resolve it into its final setting.

    Getting ready for the Installation


    First of all, the sustaining structure provided with the bathroom should be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps unit to stop pressure on the bath tub.
    Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
    Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last setting.

    Tiling Around the Bathtub


    In the location where the bath meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, leading to issues with dampness and also possible leakages to the ceiling below.
    You can pick from a variety of coloured sealers to assimilate your components and installations. They are sold in tubes and also cartridges, and are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before sealing, to permit the movement experienced when the bathtub is in use. The sealer can fracture rather early if you do not think about this movement prior to securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant sticky and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    Do you enjoy reading up on How to Install a Bathtub Yourself? Place feedback directly below. We will be delighted to know your reactions about this blog post. Hoping that you visit us again in the future. Enjoyed our write-up? Please share it. Help somebody else locate it. I truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.




    Schedule Today


    Report this page